Railroaded vs up-the-roll drapery
· DraperyFlow
Up the roll is the default for most drapery. The selvage runs vertically in the finished panel. You cut drops down the bolt, join widths at the selvage, and the pattern reads the way it was printed on the roll. Railroaded goods are turned 90 degrees: the selvage runs horizontally, and the cut that used to be a drop is now limited by how wide the bolt is.
That turn is not a preference you apply to every COM. It is a manufacturing decision. Get it wrong and either the stripe runs the wrong way, or the finished length will not physically fit in the fabric width.
Up the roll — what the floor expects
On up-the-roll drapery, yardage is widths times cut length, divided by 36. Cut length is finished length plus top and bottom hems, then rounded up to the vertical repeat if there is one. Seams run vertically. A 96-inch drop on 54-inch goods is normal. Five widths of a pair is normal. This is how almost all pinch-pleat, ripplefold, and grommet jobs are cut.
Use up the roll when the pattern must hang the way the mill photographed it, when the drop is longer than the goods are wide, or when you need vertical seams rather than a horizontal join in the stack.
Railroaded — what actually changes
Railroaded fabric is cut so the pattern or nap runs across the window. Stripes that should be horizontal, some velvets, and some wide-width sheers are sold this way. You are no longer buying a stack of drops. You are buying a continuous piece as wide as the treatment (fullness and side allowances included) and as “tall” as the bolt will allow.
In DraperyFlow, railroaded drapery yardage is the continuous cut width divided by 36, as one width. If there is a vertical repeat on the ticket, one repeat is added to that continuous width before the conversion — that is pattern matching along the rail, not extra drop on every panel. Half drop does not apply.
The length limit
Railroaded only works if finished length plus top hem plus bottom hem is less than or equal to the fabric width. On 54-inch goods with a 4-inch top hem and an 8-inch bottom hem, the longest shade or panel you can railroad without a horizontal seam is 42 inches of finished length (54 − 12). A 96-inch living-room drop will not railroad on 54-inch cloth. That is not a calculator error. The bolt is not wide enough to become the height of the curtain.
DraperyFlow flags this: if railroaded is on and the finished length plus hems exceeds the fabric width, railroading is physically impossible unless you seam horizontally — which most shops will not do on a custom drapery face.
Worked examples
Up the roll, typical pair
100 inches wide, 96 inches long, 2.5× fullness, 54-inch goods, 4 / 8 hems, no repeat. Five widths × 108-inch cuts = 15.0 yards. The drop is far longer than 54 inches, so this job cannot be railroaded on those goods.
Railroaded, a short cafe or sheers that fit
80 inches wide, 36 inches finished length, 2× fullness, 54-inch railroaded goods, 4 / 8 hems, no extra repeat. Cut length needed is 48 inches, which fits in 54. Continuous width is 80 × 2 = 160 inches. Yardage is 160 ÷ 36 = 4.44, buy 4.5 yards, one piece. Up the roll, the same job would be three widths (160 ÷ 54 rounds up to 3) × 48 inches = 4.0 yards, with vertical seams. Railroaded costs a half yard more here and removes those seams from the drop.
Romans are the same rule, different hems
A roman uses finished length plus a vertical allowance, not drapery hems, but the railroaded limit is identical in spirit: the cut in the “height” direction must fit in the bolt. On DraperyFlow’s roman defaults (8-inch allowance), a 60-inch-long shade needs 68 inches and will not railroad on 54-inch goods. The roman yardage note on this blog walks that case.
Write the direction on the work order
The mill ticket, the COM PO, and the work order should all say railroaded or up the roll. The table cannot see the designer’s mood board. If the cloth arrives already cut as drops and the spec said railroaded, you will not turn it in finishing. Calculate it once, with the toggle that matches the goods, and keep that spec on the treatment through the invoice.