Skip to content
DraperyFlow

Blog

How to calculate roman shade yardage

· DraperyFlow

Roman shades do not use drapery fullness. You are not multiplying the window by 2 or 2.5 and counting widths for pleats. You are covering a finished rectangle, then adding the hems and the board so the shade still finishes at the size you quoted. Treat a roman like a pair of pinch-pleat panels and you will buy the wrong bolt — usually too much goods, sometimes too little once the repeat is in.

This is the method a custom workroom uses for a flat roman on up-the-roll goods, and how patterned or railroaded fabric changes the buy. The allowances below match DraperyFlow’s roman calculator defaults: 4 inches total side hems and 8 inches combined top and bottom allowance. Your shop may run different hems. The structure of the math should stay the same; only the allowances move.

What you need before you touch a calculator

  • Finished width and finished length — the size of the shade as installed, not the glass alone if you have returns or a larger board.
  • Fabric width, typically 54 inches unless the mill ticket says otherwise.
  • Vertical repeat, in inches. Use 0 for a solid or a non-match stripe.
  • Whether the goods are railroaded (pattern or nap running the width of the bolt).
  • Lining plan: same cuts, or lining with no repeat.

If any of those are still a question mark in a text thread, do not order COM. The expensive error on a roman is almost always the repeat or a railroaded cut that will not physically fit in the goods.

The flat roman formula

For up-the-roll fabric — the usual case — DraperyFlow calculates as follows.

  1. Adjusted width = finished width + total side hems. Default side hems: 4 inches.
  2. Number of widths = finished width plus hems, divided by fabric width, rounded up. Minimum one width.
  3. Base cut length = finished length + vertical allowance. Default allowance: 8 inches, covering top (board, mount, closure) and bottom (hem and weight-bar pocket) together.
  4. If there is a vertical repeat, round the cut length up to the next whole repeat. Do not do this when the goods are railroaded.
  5. Raw yardage = (number of widths × cut length in inches) ÷ 36.
  6. Buy yardage = round raw yardage up to the next half yard.

Side hems are a total, not per side. A 4-inch total usually means about 2 inches per side — enough for a clean finish on a typical flat roman. If your shop double-turns a heavier cloth or adds returns on an outside mount, raise that number before you buy.

Worked examples

1. Solid 54-inch goods, one width

Finished size 48 inches wide by 60 inches long. Fabric width 54 inches. No repeat. Side hems 4 inches. Vertical allowance 8 inches.

  • Adjusted width: 48 + 4 = 52 inches. That fits in 54-inch goods, so one width.
  • Cut length: 60 + 8 = 68 inches.
  • Raw: 68 ÷ 36 = 1.89 yards.
  • Buy: 2.0 yards.

2. Same shade, 24.5-inch vertical repeat

The hems do not change. The repeat does. Round 68 inches up to the next multiple of 24.5: that is 73.5 inches (three repeats). Raw yardage is 73.5 ÷ 36 = 2.04, so you buy 2.5 yards. The extra half yard is the match, not a “safety” pad. If you skip it, the pattern will not land on the board and the hem at the same time.

3. A wide shade that needs two widths

Finished width 100 inches, length 60 inches, 54-inch goods, no repeat, same allowances. Adjusted width is 104 inches. 104 ÷ 54 rounds up to two widths. Two cuts at 68 inches is 136 inches of goods, 3.78 yards, buy 4.0 yards. You will seam. Plan the seam in the work order before anyone cuts — a roman seam in the middle of a picture window is a conversation you want to have on the estimate, not on the table.

Railroaded goods

When fabric is railroaded, the cut runs across the bolt. Yardage is no longer “widths times drop.” It is the continuous cut width divided by 36, as one piece. If there is a repeat, add one repeat to that width before you convert to yards.

Railroaded only works if the finished length plus the vertical allowance still fits inside the fabric width. On 54-inch goods with an 8-inch allowance, a 60-inch-long shade is 68 inches of cut length — it will not fit. That is not a rounding issue. It is a physical limit. Either drop to a shorter shade, use wider goods, or run the cloth up the roll.

A shade that does fit: 72 inches finished width, 40 inches finished length, 54-inch railroaded goods, 4-inch side hems, 8-inch allowance, no extra repeat. Cut length needed is 48 inches, which fits in 54. Continuous width is 72 + 4 = 76 inches. 76 ÷ 36 = 2.11, buy 2.5 yards, one piece.

Hobbled, relaxed, and ribbed styles

A flat roman is the baseline. Hobbled or waterfall folds need extra length in the loops. Relaxed and European styles need extra at the bottom so the shade can smile. Ribbed or batten-front shades need the battens planned in the stack. Do not borrow pinch-pleat fullness for those styles. Raise the vertical allowance — or the finished length you send to the calculator — to match how your shop actually builds that roman. If the style is only a label and the allowance is still 8 inches, you will cut a flat shade and try to sew folds into it.

Lining, hardware, and the work order

Lining is usually the same number of cuts, often without a pattern repeat. Interlining and blackout are their own lines, not a footnote on the face fabric. Rings, a weight bar, the board, and the control — cordless, cord loop, or motor — belong on the work order with the cuts, and they belong on the invoice as hardware, not hidden inside “fabric.”

The work order should show fabric, yardage, cut length, widths, lining, and photos. It should not show the client price. The install sheet should show finished size, mount, and control location. It should not show the cut list. If both documents are typed from memory, the roman you calculated is not the roman you will hang.

Mistakes that cost a bolt

  • Using drapery fullness on a roman.
  • Forgetting that side hems are added to finished width before you test against fabric width.
  • Ignoring vertical repeat, then discovering the hem and the board sit on different parts of the motif.
  • Railroading a shade whose cut length is longer than the goods are wide.
  • Ordering lining off the face-fabric ticket, including a repeat the lining does not have.
  • Leaving COM yardage on a napkin for the mill while the workroom uses a different allowance.

Calculate it once, then keep the spec

DraperyFlow’s roman calculator uses this structure: finished width and length, fabric width, optional vertical repeat, railroaded yes or no, 4-inch side hems and 8-inch vertical allowance unless you change them. The result sits on the treatment. From there it can become a work order, an install sheet, and the invoice — without typing 2.5 yards into a second app.

If the question on the job is not the math but who is allowed to do the math — designer or workroom — that is a separate note.

Try the full workroom for 14 days.

All-in-one workroom management software. Full Studio trial, no credit card. Keep Starter or Studio when you are ready.