Skip to content
DraperyFlow

Blog

Pattern repeat and fabric waste

· DraperyFlow

“Add 10 percent for the repeat” is not a workroom method. A 6-inch stripe and a 27-inch floral do not waste the same cloth. The extra you order is the length you throw away on each width so the motif lands on the heading and the hem the same way. That leftover is pattern waste. It is measurable. It belongs on the cut list, not in a padded quote.

If the mill ticket shows a vertical repeat, every cut is longer than the sewn length. If it does not — a solid, a non-match texture — repeat waste is zero, and the only rounding left is how you buy the bolt, usually the next half yard.

What a vertical repeat actually does

Finished length plus top hem plus bottom hem is the base cut. On patterned goods you do not cut that number. You round the base cut up to the next whole repeat so each width starts on the same point in the motif.

Waste per width, in inches, is: rounded cut length minus base cut length. Total pattern waste is that amount times the number of widths, then divided by 36 for yards. DraperyFlow’s drapery calculator does this when a vertical repeat is entered and the goods are not railroaded: cut length = the smallest multiple of the repeat that is still at least the base cut.

Worked example — straight match

A pinch-pleat pair, 100 inches wide, 96 inches finished length, 54-inch goods, 2.5× fullness. Hems 4 inches top and 8 inches bottom. Vertical repeat 24.5 inches. Side hems and overlaps set aside for a moment so the repeat is visible.

  • Widths: 100 × 2.5 = 250 inches of goods. 250 ÷ 54 rounds up to 5 widths.
  • Base cut: 96 + 4 + 8 = 108 inches.
  • With a 24.5-inch repeat: 108 ÷ 24.5 = 4.41, so 5 repeats. Cut length = 122.5 inches.
  • Pattern waste: 122.5 − 108 = 14.5 inches per width. Five widths: 72.5 inches, 2.01 yards.
  • Raw yardage: 5 × 122.5 ÷ 36 = 17.01 yards. Buy: 17.5 yards after rounding to the next half yard.

Without a repeat the same job is 5 × 108 ÷ 36 = 15.0 yards. The extra 2.5 yards on the buy is almost all match. The last half yard is bolt rounding, not motif. Those are different lines if a designer asks why COM jumped.

Half drop is not the same waste

Some prints match on a half drop: every other width is offset by half a repeat so the pattern reads across the seams. You cannot use one cut length for every width. Odd widths round the base cut to the repeat. Even widths round the base cut plus half a repeat to the repeat. DraperyFlow’s half-drop toggle does that alternating math. It only applies when there is a vertical repeat and the cloth is not railroaded.

Example where half drop actually adds goods: four widths, base cut 108 inches, 27-inch repeat. Straight match cuts all four at 108 inches — 12.0 yards. Half drop: odd widths stay 108; even widths need 108 + 13.5, which rounds to 135 inches. Two of each is 486 inches, 13.5 yards. The extra 1.5 yards is the offset, not a safety pad. If the mill ticket says half drop and you buy straight match, the table will be short on the even widths.

What not to do

  • Do not add 10% or “a yard for luck” instead of rounding to the repeat. A small repeat wastes little; a 27-inch floral can waste most of a repeat on every width.
  • Do not take the designer’s “about 12 yards” and then add repeat on top of an already padded number. You will double-count.
  • Do not apply vertical-repeat rounding to railroaded goods. The cut is across the bolt; pattern waste is handled on the width, not as extra drop on every panel.
  • Do not put lining on the same repeat as the face unless the lining is patterned. Most linings have no match. Buying lining to the face-fabric ticket is how shops over-order ivory sateen.

Horizontal repeat

Horizontal repeat is how often the motif repeats across the bolt. It matters when you seam widths and when you decide where a join sits on a picture window. It does not replace vertical-repeat waste on up-the-roll drapery. If the mill gives both numbers, use vertical repeat for cut length and keep the horizontal number on the work order so the table can plan the seam.

Order the calculated buy, not a percentage

The COM PO should show the same yards as the work order: repeat-rounded cuts, then shop rounding to the next half yard. DraperyFlow keeps that number on the treatment so the mill, the table, and the invoice are not three versions of “extra.” If the cloth is railroaded instead, the waste shows up in a different place — that note is next.

Try the full workroom for 14 days.

All-in-one workroom management software. Full Studio trial, no credit card. Keep Starter or Studio when you are ready.