Drapery returns and overlaps explained
· DraperyFlow
Window width is not the width of the cloth. A pair has to wrap to the wall, meet in the middle, and still turn a hem on every vertical edge. Those three additions — returns, overlap, and side hems — are why two shops can quote the same glass and buy a different number of widths. If they are missing from the calculator, the panels will look skimpy on the rod or they will not close.
Return
A return is the fabric that turns from the face of the rod or board back to the wall. It hides the bracket and stops light at the stack. On an outside-mount pair you usually have a return at each end. The depth follows the hardware: a 3½-inch projection wants about 3½ inches of return, plus whatever your shop adds so the hem clears the bracket. Inside-mount panels often have little or no return; the stack sits in the opening instead.
Measure return from the face, not from the wall, if the rod already sits off the plaster. Copying “3.5 inches” from the last job when this rod is a 5¼-inch double pole is how pairs come up short at the wall.
Overlap
Overlap is where a pair meets at center. Each leading edge needs enough cloth to pass the other panel so you do not get a vertical slit of daylight. A common shop figure is about 3½ inches per leading edge, or one overlap total in the 3- to 4-inch range if you count it once on the pair. Ripplefold on a ripple carrier has a defined overlap on the master; pinch pleat is a sewn leading edge. The number changes with heading. What does not change is that a pair needs it and a single one-way panel does not need a center overlap.
Side hems
Side hems are the turn-under on the vertical edges — leading edges and return edges. A double 1½-inch side hem is a typical US workroom finish on drapery. That is not fullness. Fullness is the gather or pleat across the window. Side hems are finishing. If you only multiply width by 2.5 and never add hems, the finished pair is narrower than the rod once the turns are sewn.
Pair versus one-way draw
- Pair, split draw: two returns (left and right) + center overlap + side hems on four vertical edges.
- One-way draw: one return on the stack side, a leading edge on the other, no center overlap. Less extra width than a pair.
- Two panels on a continuous rod with no overlap (decorative, not closing) still need returns and hems; they do not need a closing overlap.
How this hits the fabric buy
Fullness is applied to the window first. Returns, overlap, and side hems are added after that, as extra inches of goods, before you divide by fabric width and round up. DraperyFlow’s drapery calculator uses one field for that extra: side hems, default 10 inches, added after fullness. That 10 inches is a practical total for a typical pair — returns plus overlap plus hems — not a per-edge measurement. If the rod is deep, the overlap is large, or the heading is ripplefold, raise the number. If the job is a one-way inside mount, lower it.
Those extra inches matter when you are close to the next width. Example: 85-inch window, 2.5× fullness, 54-inch goods.
- Window × fullness: 85 × 2.5 = 212.5 inches. 212.5 ÷ 54 = 3.94, so 4 widths — if you add nothing for returns and overlap.
- Add a 10-inch pair allowance: 222.5 ÷ 54 = 4.12, so 5 widths.
That is a full extra drop of goods because 10 inches pushed you over the remainder. On a 24.5-inch repeat the extra width is not “10 inches of cloth.” It is another cut at the full cut length. Missing returns on a job that sits at 3.9 widths is one of the quiet ways a shop under-buys COM.
Put the numbers on the install sheet
The work order needs the cut. The install sheet needs the return and the overlap the crew will see on the rod — projection, whether the pair meets, which side a one-way stacks. Those are not the same document. If both are generated from the same treatment, the 10 inches you added in the calculator should match the hardware on site. If the installer shows up with a deeper pole than the spec, the return you bought will not wrap.
Calculate fullness, then add the pair (or one-way) allowance, then match the repeat. Do not bury returns inside a higher fullness “to be safe.” Fullness changes the look of the pleat. Returns change whether the panel hits the wall.